electrolight XH-M600 Charge Control Module 6-60V Storage All types of Battery charging Protection Board charger controller for 12v 24v 48v battery Micro Controller Board Electronic Hobby Kit

XH-M600 Charge Control Module 6-60V Storage All types of Battery charging Protection Board charger controller for 12v 24v 48v battery 1.Model:XH-M600 2.control voltage :DC 6-60V 3 control current: max 30A 4 Control Precision:0.1V 5 Output Type:direct output 6 Voltage Tolerance:+/-0.1V 7 Application Fields:6-60V battery 8 Size:84*60mm Using Method: 1:connect to battery(if not,won't have display) 2:press the "+" display upper limit volatge , long press will flashing ,then set the upper limit volatge (H) 3:press the "-" display lower limit volatge , long press will flashing ,then set the lower limit volatge (L) 4:connect to the charger 5: can press the set close the display save electricity Specifications: Product Name: CNC charging module Product Type: XH-M600 Control voltage: DC6-60V Control current: ? 30A Control accuracy: 0.1V Output type: direct output Voltage error: ± 0.1V PCB size: 84 * 60mm Scope: all kinds of storage batteries and lithium batteries Failure analysis: 1. Q: How many V batteries are suitable for use? How many V voltage does this module fit? A: This section is suitable for minimum 6V maximum 60V voltage range, the maximum support battery 48V, because the 48V battery is fully charged about 60V or so. otherwise the product will burn. 2. Q: Why is the connection on the charger module not shown? A: There is no battery or battery voltage is less than 6V, because the motherboard power supply from the battery - will be connected to the battery board to display, only the charger is not displayed! 3. Q: How to set the start-up voltage and stop voltage? A: For example, set the starting voltage to 12.5V, stop the voltage of 14.8V. It is recommended to set the stop voltage and then set the starting voltage. Step: Press the + key to display the voltage at the beginning of H. Press SET at this time (you can also press and hold the key to enter). At this time, the value of H starts flashing through the + - key to H14.8. Ok. Start the voltage method the same: press the - key to display the voltage at the beginning of the L at this time press the SET, L start the value of the flash through the + - key is set to L12.5, so start the voltage to set OK 4. Q: start the voltage can not tune up A: Because the module is only charging function limits the start value ? stop value, so to increase the start value, it is necessary to first stop the value! 5. Q: After power on the relay crackling! The indicator light flashes A: This is because the charging current is too large or the battery capacity is too small to cause a power is immediately pulled to the stop value, to stop the value of the module after the power, the voltage quickly dropped to the start value and began charging, Loop. At this point as long as the lower charge current, usually the charge current is the capacity of 10 to 1 to 1.5, such as 20AH battery charging current is 2-3A or so! Pay attention to high current charging will cause the battery to accelerate the aging of heat, drums and even explosion! 6. Q: What control can automatically pass the bad charge? Can you use edge Can I limit current? A: This is the voltage control, for example, set to start 12V to stop 14.5V, when the voltage rushed to 14.5V this value on the power, the voltage down to 12V and closed charge You can use the edge of the red, the voltage control mode only to turn off and turn on, can not limit current, charging current depends entirely on your charger 7 Q: Input 12V can not charge 24V battery, or input 48V can give 12V charge? A: The product is a simple voltage controller, only play the role of switching, can not change the pressure to the battery charge, so what charge should be prepared to charge what charger!