WRAP AND RIDE Sticker & Decal for Bike  (Multicolor)

HOW TO INSTALL WRAP How to install your decals, graphics and race numbers? Check out our Application Process and videos to get the most out of your decals. We will describe how to get the most out of your new decals and prolong their life. Below you will see 3 steps. Step 1 Remove Old Wrap Step 2. Arrival of New Wrap And Ride Kit (Storage & Preparation) Step 3. Applying Your New Wrap STEP 1. REMOVE OLD WRAP We highly recommend giving your vehicle a good clean. The cleaner your machine the better the results you’ll get in applying your decals. DO NOT USE LUBRICANTS JUST BEFORE APPLYING WRAPS We suggest that you strip your bike of your old decals that you no longer need (only do this for the decals you have just ordered – not the ones you want to remain on the vehicle) The effort required when removing decals can differ depending on the quality of your old decals. With a very good quality decals (like Wrap And Ride’s decals) you can simply heat the decal with a hair dryer (not too much) then start to peel it off slowly and continue to peel until the decal is completely removed from the surface of the vehicle. Now your old decals are removed Now that you have your decals removed you want to prepare the surface to ensure there is no film of dirt, grease, or any other barrier that may inhibit the decal from getting the proper adhesion to the vehicle surface. Use a lint free cloth (a cloth that doesn’t give off any fabric from the cloth) and spray the machine surface. You can leave this on for a minute or two to break down the film of dirt/grease. Then wipe off to fully remove. The clearer the surface the better your new decals will stick. If you have adhesive left on the surface of your machine you will need to either: • Use a heat gun/hair dryer to break down the adhesive and scrape off • Use adhesive removal and then scrape off the adhesive You will never have to do this with Wrap And Ride’s decals as our material is superior to most and we never use lower quality materials that will do this. Now your machine is fully prepared for your new designed graphics kit. STEP 2. ARRIVAL OF NEW WRAP AND RIDE KIT. When your designed decals arrive they will be in flat packed. We test all our decal materials and only handle them in accordance with testing. Flat Package STEP 3. APPLYING YOUR NEW WRAP Your vehicle and your decals are ready for installation and it’s time to apply your graphics to give your bike a facelift! It will make a serious difference to your machine’s appearance. It’s helpful to apply the centre strip of the decal and slowly ease out the decal to the extremities of the plastics. If you gently ease the decal out from the centre with your fingers it can give the decal the heat it needs to stretch the necessary amount to perfectly conform. Only do this when you are sure you have the decal correctly aligned with the plastics. You can peel back the decal to remove any air bubbles that might appear during the installation. You can remove the decal many times in the adhesion process but you must ensure you don’t stretch the decal (by pulling to roughly) when removing it for correct re-alignment. When you are completely happy with the decal installation you can apply gentle heat (not too much) over the decal with a hair dryer (avoid heat gun as it provides too much heat) to help the decals take the shape of the plastics. You can also use heat when applying thicker materials but be careful as you don’t want to warp/distort the shape of the decals so they can’t fit your vehicle. Your decals should now be perfectly applied. Note : Wrap And Ride prides itself on its worldwide customer base. Motorsports are practiced far and wide across the globe on the fastest tracks, highest mountains, wild-breaking waves and deserted deserts. This is exactly where you will find Wrap And Ride customers! Our delivery schedule is from the time of purchase. We pride ourselves on getting your graphics to you as soon as possible. ¬ WE WOULD LOVE TO HEAR FROM YOU, IT’LL HELP PROVIDE BETTER SERVICE. If you have any issue with your delivery, want to know more or give us feedback please contact us on official.wrapandride@gmail.com We would love photos of your new decals on your machine to showcase on our social platforms.Please send them via mail on official.wrapandride@gmail.com FIND US ON • FACEBOOK/WRAPANDRIDE • INSTAGRAM/WRAPANDRIDE • YOUTUBE/WRAPANDRIDE